K40 Laser Cutter: How to Cut and Engrave in One Job

K40 Laser Cutter: How to Cut and Engrave in One Job

The K40 is a budget friendly desktop laser cutter. However, considering that the hardware and software is directly exported from China, it is not user friendly at all. This tutorial shows the end-user how to cut and engrave a pendant in one fell swoop.

Note: This tutorial assumes that you already have the laser cutter setup and the software installed.

Task 1: Think of a concept.

In this scenario, I am cutting out a lucky charm pendant, but feel free to vary from this design.

Task 2: Now that we have a design, launch CorelLASER from your desktop.

K40 Laser Cutter: How to Cut and Engrave in One Job

Task 3: CorelLazer Preliminary Settings

K40 Laser Cutter: How to Cut and Engrave in One Job

Before you start designing your pendant, do yourself a favor and change some preliminary settings within CorelLASER. First, change the units to centimeters. Then change your canvas size to 30cm x 20 cm. We change this because this is the maximum cutting area of the K40’s bed.

Task 4: Enabling Object Manager

K40 Laser Cutter: How to Cut and Engrave in One Job

Next,go to the Tools > Object Manager. Once clicked it will add a new pane on the right hand side of CorelLASER.

Task 5: Within the Object Manager pane, click new layer.

K40 Laser Cutter: How to Cut and Engrave in One Job

Task 6: Rename Layer 1 to Cut, and rename Layer 2 to Engrave.

K40 Laser Cutter: How to Cut and Engrave in One Job

Task 7: Creating an Anchor Pixel in the Cut Layer

K40 Laser Cutter: How to Cut and Engrave in One Job

Make sure the Cut layer is highlighted and place a pixel sized square in the top right hand corner of our drawing.

Note: One of the many quirks of the K40 laser cutter is that you need to put a
pixel in the very top left of your layers. If this is not done, then for some reason the laser cutter doesn’t know how properly line things up (between the cutting layers and the engraving layers).

Task 8: Draw the Shape of your Pendant

K40 Laser Cutter: How to Cut and Engrave in One Job

Now that all the preliminaries are taken care of lets start to design the shape of our pendant. Make sure the Cut layer is selected and draw a circle. I made my circle orange (for visibility) with the diameter of 3 centimeters.

Note: There are numerous intricacies involved with CorelDraw / CorelLaser. This you will have to learn on your own. ALSO, the K40 software cuts anything that is NOT white.

Task 9: Hole for the Jump Ring

K40 Laser Cutter: How to Cut and Engrave in One Job

Now that we have the outline of our pendant, draw a small white circle within the large red circle. This is where you would place your jump ring. I made mine .25 centimeters in diameter.

Task 10: Creating an Anchor Pixel in the Engrave Layer

K40 Laser Cutter: How to Cut and Engrave in One Job

Make sure that the Engrave layer is selected. Place a small 1×1 pixel in the very top left hand corner of our drawing.

Task 11: Creating the Pendant Border

K40 Laser Cutter: How to Cut and Engrave in One Job

For the border of the design I found a Celtic circle with a transparent background. I imported this design into the drawing and re-sized it. Again this is done on the Engraving layer.

Task 12: Adding the Four Leaf Clover

K40 Laser Cutter: How to Cut and Engrave in One Job

Next I was able to find a four leaf clover design that I liked and imported it into the Engraving layer.

So our design work is now complete. Pat yourself on the back. The next series of steps explain how to feed this data to the K40 laser cutter.

Task 13: Configuring our Data Formats

K40 Laser Cutter: How to Cut and Engrave in One Job

Click the small green pencil icon at the top of CorelLAZER. This will launch a window that allows you to configure the format of the information going to the laser cutter. Make sure that the settings are configured to the following:

Engraving data: WMF – Normal Windows Metafile
Engraving Area: Only Selected
Cuting data: WMF – Normal Windows Metafile
Cutting Area: Only Selected.

Note: If you choose other data formats, such as PLT, your cuts may be off.

Task 14: Hiding the Cut Layer

K40 Laser Cutter: How to Cut and Engrave in One Job

Next click the small eye icon beside Cut layer. This will hide everything we created in the cut layer.

Task 15: Select the Engraving Layers

K40 Laser Cutter: How to Cut and Engrave in One Job

Using the pointer tool click and drag to select everything on the engrave layer. Notice on the Object manager pane, all the designs are highlighted in blue.

Task 16: Click the engraving button towards the top.

K40 Laser Cutter: How to Cut and Engrave in One Job

Task 17: Configuring the Engrave Settings

K40 Laser Cutter: How to Cut and Engrave in One Job

There are some important parameters that need set within the engraving window.

We want origin to be at the very top right, so set Refer-X to 0.0000 and set Refer-Y to 0.0000. While on the engrave window, set the Method to Dialog and click add task. After hitting Add Task, the window should close. This tells the laser cutter that this is one of two tasks. Also, it is not a bad idea to make sure your speed is set appropriately. I believe I that 175.00mm/s is a good speed, but then again it all depends on what type of material you are engraving.

Task 18: Hide The Engrave Layer, Enable the Cut Layer

Now that we have the laser engraving setup to our liking. Let’s begin on the cutting aspect of things. Click the eye beside the engraving layer to hide the shamrock and border. Click the greyed out eye beside the cut layer to once again reveal our orange circle.

Task 19: Click and drag to select all the shapes within our cutting layer.

K40 Laser Cutter: How to Cut and Engrave in One Job

Task 20: Click the Cutting Icon at the Top.

K40 Laser Cutter: How to Cut and Engrave in One Job

Task 21:

K40 Laser Cutter: How to Cut and Engrave in One Job

Whenthe cutting window pops up, Make sure your Speed is set to the appropriate setting. For this project I was cutting wood so I did 2 passes 10mm/s @ 50% power. Make sure your origins are set to the appropriate positions (Refer-X: 0 Refer-Y:0). Make sure that Method is set to dialog. This is because this is task 2 of 2. Make sure that the Starting checkbox is selected. This check box means that the laser cutter will begin cutting as soon as you click Add Task.

Task 22:

K40 Laser Cutter: How to Cut and Engrave in One Job

Click Add Task. If everything goes correctly the laser cutter should start to engrave your project and ultimately cut your project.

For your convenience, I’ve attached the CorelDraw file to this instructable. If you are running into problems, it might be able to help you out!

Thanks for looking at my Instructable.

K40 Laser Cutter: How to Cut and Engrave in One Job

Pendant_Instructable.cdr

laser-cutting – K40 Laser Cutter: How to Cut and Engrave in One Job, in category: workshop

Written by admin